Tag Archives: bass vi

Demystifying Part 5: The Fender Mute

After a years-long hiatus, the Demystifying series is back!

First, I need to say thanks to all of you that have checked out the blog, and in particular the many that have shared and reposted these articles. Because of their popularity, Premier Guitar recently asked me to write an offset guitar setup guide for publication, which you can find in the May 2017 issue. AVAILABLE NOW IN STORES AND ONLINE!

So thanks to all of our readers, customers, and friends––without your support, this never would have happened.
The one bit of hardware I’ve not discussed previously is often thought of as a vestigial, an hold-over from a different time fit for the bin. Ultimately, it’s up to you if you’re ever going to use the thing, and to be honest, it seems like many don’t. However, if you’ve ever been curious about it, or if you use it but find it problematic, then friend, I come bearing glad tidings. I am of course talking about the Fender Mute.

A feature shared by both the Jaguar and Bass VI – though not across all models or years of production – this curious metal plate was originally intended to be a surrogate for palm muting. Couldn’t be a simpler mechanism, really: the mute is secured to the body by two screws, and the long bolt in the middle pivots on a spring-loaded plunger sunk into the guitar body. The mute can be engaged by pressing on the plate, shifting it back and forth in place, causing the foam pad to make contact with the underside of the strings.

The Fender Mute leaves the player’s picking hand totally free for strumming or sustain-less leads. This gives the device a sound distinct from traditional palm muting techniques, one widely used on instrumental surf recordings of the 1960s. What’s it sound like? I just happen to have an example for you here:

Like the Fender offset bridge, the mute requires some extra thought to set up correctly. Really, the whole procedure comes down to balance; the mute has to be set to engage smoothly while allowing the bridge to be lowered enough for playable action. If the mute sits too high, the bridge will rest on its mounting screws. Too low, and the mute won’t engage at all.

It’s best to begin with the mute installed on its own––leave the bridge for later. Remember those two mounting screws I mentioned earlier? You’ll need to find the lowest possible setting for them where the mute still pivots. Try screwing them in all the way, then backing off until the foam side of the mute pops up and stays put. Then, install the bridge and make sure it doesn’t sit on top of the mute mounting screws.

It may take a few tries, but you’ll soon find that balance. When pressing on the plate, the foam side should rise up to meet the strings but not push them up, then stay firmly in place. Pushing down on that side should disengage the mute, again with a firm action. If the mute doesn’t stay in place, or is difficult to move, take the bridge off and keep adjusting those mounting screws.

Top: disengaged. Bottom: engaged

It’s worth noting that, In order to get the mute set up correctly, your guitar will need to be shimmed as described in part two of the Demystifying series. A sufficient amount of neck angle is crucial, otherwise there may not be enough room under the bridge for the mute to be functional.

One problem that can crop up with the mute is that it pulls the strings sharp when it’s engaged. Often, this can be due to the mute sitting too high, which effectively shortens the scale length of the instrument. If that’s the case, cranking down the mounting screws should solve this issue for most players. Too-hard foam can also be the culprit, pushing up on the strings and raising pitch. Substituting a softer piece of foam here can work wonders (more on that later). Alternatively, one can easily shave off the bit of foam that touches the strings.

If you have a vintage Jaguar or Bass VI, you’re likely familiar with a problem that arises when the original foam on vintage instruments, due to age or contact with sweat: deterioration. This happens to pickup foam as well, where it hardens and compresses, rendering pickup height adjustment difficult or even impossible.

Hardened, sticky mute foam on a refinished ’63 Jaguar. You can see the gooey residue on the low E side of the mute.

If this happens to your mute foam, I have to tell you there’s no point in trying to salvage it. Touching or removing the stuff, you’ll notice that what was once foam is now a slightly gooey, sticky mess. Even on a totally original ‘60s guitar, leaving foam in this state is at the very least off-putting and potentially problematic, what with the black residue left behind on contact with skin or strings. Seriously, that stuff is disgusting.

Do yourself a favor and replace that foam. I’ll admit, it’s often the only part we’d even thing of replacing on a perfect vintage Jaguar. Replacement Fender foam can be found on eBay, but it seems that every parts supplier is out of stock right now. In a pinch, we use this. The link will take you to some weather stripping foam that’s just slightly taller than the 3/8” by 1/4” Jaguars have from the factory, but it should work like a charm. If the extra height concerns you, the same brand has a version with a height of 3/16″ as well.

Interestingly, this Mute wasn’t Fender’s first shot at string-dampening technology. Earlier, there was foam stuffed under the bridge covers of ‘50s Precision basses. The first Jazz Basses featured stiff pads for each individual string, while the later Mustang Bass  bridge had similar devices. Muting may make a bit more sense on bass than guitar, but give this mute system a shot and see if you can’t make it work for your brand of music. To the author, it’s a fun sound that makes some rhythm parts more interesting, and with effects added, it can bloom into something totally unique. And weird. Definitely weird.

Tagged , , , , , , , , , , , , , ,

The Squier Vintage Modified Bass VI: a 100% Pun-Free Upgrade Guide

img_7827

My Squier VI lounging with Paul Frank’s amazing Custom Shop model, strung with Gabriel Tenorio strings

While Fender’s Jazzmaster and Jaguar seem more popular than ever, the Bass VI still seems mysterious, or at the very least, under-appreciated. Players seem confused by its mere presence in the catalog: Is it a bass? Is it a guitar? Is it a baritone?

Let’s clear up the confusion right now: The Bass VI is a bass guitar in the strictest sense. Tuned E to E a full octave lower than a standard guitar, the VI is an incredibly versatile instrument that’s as well-suited for familiar chord shapes as it is for punchy bass lines.

Right now, the easiest way to get into a VI is the Squier Vintage Modified model. Fundamentally a great instrument, the Squier VI ticks all of the right boxes for me: it has Jaguar-style pickups and the all-important fourth Bass Cut switch, it’s affordable, and it’s damn fun to play. We’re still talking about an import model, so if you pick one up and find it lacking, I’m here to provide a handy upgrade guide to the “ba-VI” of “VI-sessfully” upping your Squier’s “VI appeal” into a machine for making “mu-VI.” (My deepest apologies for how poorly those puns worked.)

The first mod I’m going to suggest can hardly be called a mod at all, but believe you me, it’s crucial.

STRINGS

Far and away, the most common complaint with current Bass VI models is that the low E string lacks tension. You’ll hear it described as “floppy” or “sloppy,” and those adjectives sum it up nicely. It feels unbalanced and just can’t stand up to aggressive picking.

The problem with your Bass VI’s low E is thanks to a too-light gauge of string. When Fender released the Bass VI in 1961, the standard set was made up of strings gauged .026”-.095”, and that .095” is key here. At some point in the recent past, the low E string changed to .084” which is woefully under-built for the task. A .095” E is going to feel taut, stable, and will gleefully accept heavy attack, whereas the lighter string ends up feeling, well, just as described in the paragraph above.

In my view, the most essential mod you can perform on your VI is installing a heavier, more balanced string set. Even without upgrading the bridge or swapping pickups, this very simple and easily overlooked tweak can tighten up the whole instrument and bring back the low end that’s so sorely missing with the stock strings.

Because this information doesn’t seem to be collected anywhere, here’s a handy shortlist of string makers that offer a good set of VI strings with adequately heavy E string, which I’ll update as I stumble upon them. The only set Fender currently offers is gauged .024″-.084″, sadly.

La Bella (Flats and Rounds)
Kalium (Rounds, tons of options)
Gabriel Tenorio String Company (Rounds and Gabriel’s new Ground Wounds)

Or, if you want a genuine set from the 1960s

BRIDGE

A '62 Bass VI that I recently fell in love with at the Fretboard Journal Summit, courtesy of Gryphon Stringed Instruments

An original ’62 Bass VI that I recently fell in love with at the Fretboard Journal Summit, courtesy of Gryphon Stringed Instruments

If you ever have a chance to inspect a vintage Bass VI, you’ll notice that the original bridge is much wider than the one found on most reissues, which is just a standard offset bridge slapped on likely due to the costs of tooling-up for such a niche item. That original 1” width is a big part of the Bass VI functionality puzzle, which translates to more flexibility when it comes to intonation. Original examples have nearly twice the saddle travel as the current part, and with the Bass VI’s 30” scale, every little bit is precious.

The stock Squier VI bridge

The stock Squier VI bridge

The bridge found on the Squier Bass VI is essentially the same as the other VM offsets, save for the adjustable Mustang-style saddles, which have deep grooves and the ability to set the radius of the strings to match the fretboard. It does, however, have a propensity to rattle around so much that even correct offset setup techniques may not quell it. (See my Demystifying series for more info)

What to do? Track down an original bridge from the 1960s or 1970s? Nah, Staytrem’s got you covered with their fantastic and appropriately wide Bass VI bridge. If you’re looking for a stable bridge that’ll intonate for sure, this is the way to go. I have a Mastery on my personal Squier, and while it does intonate perfectly for me, your mileage may vary depending on string gauge and type as well as setup.

TREM

img_8743As I mentioned in my recent article on the J.Mascis model, if you’re planning on using the vibrato you really should upgrade this part. Import vibratos are made of inferior metals and often have manufacturing flaws that render them less stable than their US-made counterparts.

A great solution here is obtaining a Fender AVRI/AV65 vibrato, especially if you’re on a budget. I’ve chosen the Mastery Vibrato for my own specifically because of the heavy-duty spring Mastery uses, which replicates the sturdier feel of early 1960s units and really stands up to the extra tension of those thick strings.

 

NUT

As you might expect, the nut work on these instruments is passable, but not great. The soft plastic used wears easily, and the slots are often too tight even for the string gauge used at the factory. I’ve also seen a number of them with poor string spacing, but hey, I don’t expect perfection on a sub-$500 instrument.

I highly recommend having the nut replaced by a competent tech in the material of your choice; my preference is bone. And for those of you that use the vibrato, a properly-cut nut is your best defense against tuning issues.

ELECTRONICS

The electronics in the Squier Vintage Modified series are, understandably, on the cheap side of things. I’ve seen and heard of a number of VMs that had wiring issues or faulty parts right out of the box, so if you’re going to be using this instrument heavily I would insist that you have the instrument rewired with higher quality pots, switches, capacitors, and even replace the jack while you’re at it. Not only will you end up with an instrument you can really trust, you’ll also have better sound as a result.

Look to CTS, Bourns, or my good friends at Emerson Custom for pots, Switchcraft for the jack and switches, and any number of options exist for capacitors. Most of these parts can be found via AllParts or Angela.

Note: US parts will require enlarged holes on the volume-tone control plate.


PICKUPS

While I confess that you can get by with the Squier in its stock configuration, let’s be honest: there are better pickups out there. They’re a little trebly, a bit noisy, and too weak on output to keep up with other basses. It’s well worth your time to explore the myriad pickup options that exist in today’s market, but where to start?

Star Trek stickers optional, of course

Star Trek stickers optional, of course

In my mind, Curtis Novak has his finger firmly on the pulse of offset guitars’ unique capabilities, and he’s the first person I bring up when a customer has a specific sound in their head. From traditional sounds to obscure designs stuffed into familiar covers, Curtis excels at wringing every last drop of tone from your instrument.

For Bass VI, he offers both the early ’61-’62 Jack Bruce-style pickups and the Jaguar-style pickups that came as standard on the model from 1962 onward. However, if you’re looking for something different, I’m sure Curtis could wind up a trio of his Jaguar-sized Lipsticks, some unique Gold Foils, or even something humbucking if you’re that kind.

Another good option would be the fantastic pickups made by our friend Jaime of At The Creamery. He offers a VI set with much higher output than the stock pickups, and with custom options if desired. Jaime does exceptional work!

On my personal VI, I started out by building a set out of three Fender AV65 Jaguar pickups, which I really like. They’re affordable and great-sounding pickups for the price, but ultimately, a little too bright for my tastes. If you need a good Tic-Tac sound, this would be a great way to go. If you create a set out of three separate pickups, do pay attention to output in each position as well as polarity to make sure they all play well together.

Currently, my VI is loaded with a set wound by our good friends a Lollar Pickups, which have a bump in midrange and output, and they really keep up with my other instruments no matter the setting. Plenty of bass on tap and clarity through any amp. I’m a huge fan of Lollar Pickups.

TUNERS

Prepare to be amazed: there’s no good reason to toss these. The Kluson-style tuners you find stock on the Squier VI are great. On the many examples I’ve had across my bench, I have never found them to be problematic. Keep them.

LINE VI

When Squier introduced their take on the VI, I was immediately excited. At the time, the VI wasn’t an instrument I was keen to spend a lot of money on, simply because I didn’t think I’d be using it heavily. Squier made that sound accessible and did so with a lot of bang for the buck. When you mod this instrument, it isn’t so much a lipstick-on-a-pig scenario, you’re genuinely taking a good instrument and making it better.

My VI and '73 Precision, just after we got back from tour.

My VI and ’73 Precision, just after we got back from tour.

To that point, I recently joined my good friends Vanessa and Sarah, a duo better known as Leo Leo. The LA-based contemplative rock-pop outfit plays complex, beautiful music that’s as energetic as it is challenging; they are one of my favorite bands. When they asked me to tour with them on bass, I have to admit that I was overjoyed and overwhelmed, especially with just a week to learn ten songs. It was a lot of work, but I’m so proud of the noise we made together at those shows.

At the center of my bass sound: my trusty Squier VI. I plugged into a borrowed Salvage Custom board (thank you, Gabriel!) populated with pedal necessities run through a mini SVT. Night after night, that thing performed beautifully and never let me down. Even as we rehearsed, it became clear that the VI was the sound. It proved to be such a bruiser that next time, I may leave my ’73 Precision Bass at home.

Each time I took it out of its case, I was immediately greeted with questions from perplexed onlookers that wondered about my weird bass. I showed it off proudly and handed it over to person after person, none of whom could believe what they were playing was a lowly Squier. There was only one occasion before a show where a churlish bassist chided me for playing––and I quote––a “piece of shit.”

I’m happy to say that I proved him wrong that night. I’m proud to play my Squier.

Here's how that Squier looked the day I recieved it. (Thanks, Nate!)

Here’s how that Squier looked the day I recieved it. (Thanks, Nate!) See below for a post-mod comparison.

This one's getting a TON of use in the @leoleoband set for the tour that starts—holy shit—tomorrow. Now, the weight of this Squier Bass VI never bothered me until we started this hours-long rehearsal process, but at the end of the night my back is screaming at me for relief. I think it may be time to look into a real '60s VI refin or something, that is of course assuming that the band wants to keep me! 😁 I also wish it were brightly-colored, but eh, such is life. Upgrades: -Lollar pickups -Fenderparts mint guard -Mastery Bridge + Vibrato (thanks Woody!) -upgraded wiring -La Bella Deep Talkin' Flats -Matching headstock #guitar #bass #bassvi #leoleo #tour #masatour #makeamericashakeagain #squier #fender #offsetguitars #lollarpickups #masterybridge #fenderparts

A post shared by Michael James Adams (@puisheen) on

Tagged , , , , , , , , , , , , , , , , , , , , , , , , ,

Dueling Summits

Owning your own business means wasting time whenever you feel like it! For instance, say you had a particularly nice Paul Rhoney-built Bass VI in for some minor tweaks, and you were able to convince Other Mike that this was a good idea:

Damn fine coffee! And hot!

Tagged , , , , , , , , , , , , , , ,
%d bloggers like this: